HomeAssistant - Polyaire AirTouch 4 Integration

Related tags

Hardwarehass-airtouch4-platform
Overview

HomeAssistant - Polyaire AirTouch 4 Integration

Custom integration to add an AirTouch 4 AC Controller

Installation:

Copy contents of custom_components/polyaire/ to custom_components/polyaire/ in your Home Assistant config folder.

Installation using HACS

HACS is a community store for Home Assistant. After installation, add this repository to HACS and install the polyaire integration.

Requirements

AirTouch 4 console IP address is required when installing the integration

Services

This custom component creates:

  • one device for each AC unit installed
  • one climate entity for each AC unit installed
  • one fan entity for each group defined, which controls the zone damper
  • one climate entity for each group with ITC installed, which controls the group temperature

For each group with ITC, the fan entity can switch between 2 profiles:

  • Damper - which allows direct damper control via the fan
  • ITC - which allows for temperature control using the ITC
Comments
  • Sensors not updated automatically when changes are made on wall controllers

    Sensors not updated automatically when changes are made on wall controllers

    Updated to version 1.3 (PUSH) which seems to work except that sensors aren't updating automatically when changes are made to target temperature or zone on/off state, either on the AirTouch 4 tablet or on ITC switches.

    I can force updates to happen for all zones by using NodeRed to change the target temperature of a single zone by 0.1 degree. I've set NodeRed to do that every minute. Hopefully you can find some way of automating that in the integration?

    opened by spry-salt 7
  • Room Thermostats all show as Cooling even when heating

    Room Thermostats all show as Cooling even when heating

    I have Airtouch4 in home assistant then linked to HomeKit. Firstly, it works great thanks.

    But the room thermostats in HomeKit all display 'Cooling to ..' when turned on. This occurs no matter the mode of the main thermostat. For example we now have heating running but rooms still read as cooling.

    Is it possible to adjust this?

    Thanks

    opened by kylecwhite 6
  • HA Reboot requires Integration disable/enable

    HA Reboot requires Integration disable/enable

    After a reboot of home assistant the integration has an error stating it is unable to contact the AirTouch controller. Disabling and re-enabling the integration resolves the issue.

    Have looked at the home assistant logs but nothing is posted in there to explain the issue

    opened by salty2011 5
  • Current Temperature as its own sensor

    Current Temperature as its own sensor

    Problem Statement When using something like Dwains dashboard the current temperature is not display while AC unit is set to off, and when it is on it will display the desired temp instead of the current temp

    Possible Fix Not entirely sure, but perhaps the below

    • Move current_temperature attribute to its own sensor and make the attribute temperature
    • on the itc sensor rename temperature to target_temperature
    opened by brine0m 1
  • Set HVAC mode doesn't work if target mode is already current mode

    Set HVAC mode doesn't work if target mode is already current mode

    When trying to create automations I found that if you try to set the HVAC mode of an ITC to "off" when it is already "off" this can result in the ITC switching to auto.

    opened by MinimalMule 0
  • Push subscription seems to expire after a quantity of hrs

    Push subscription seems to expire after a quantity of hrs

    I haven't been able to calculate the exact duration, but if no command is sent from HA to AT4 and everything is idle, after 10-24hrs I stop receiving ITC temperature updates. As soon as I touch/adjust any parameter in HA, everything comes back to life again for another 10 or so hours.

    I've yet to check if during a time HA is not receiving updates, if I make a change within AT4 things come back to life again.

    Maybe we need a 6-hourly poll just to ensure things stay active? [edit] If the master 'AC' is turned on/off in HA, this does not trigger an update to the ITC states. A change to a zone is required for updates to start flowing in again.

    Screenshot 2021-12-03 092627

    opened by t1mb0 5
Releases(v.1.4.4)

  • v.1.4.4(Jul 15, 2022)

    Changes:

    • fixed bug that would disconnect the plugin very often and cause slowdowns
    • fixed bug that would add ITC battery to zones without batteries

    Enjoy! If you found this useful, say Thank You! with a beer.

    Source code(tar.gz)
    Source code(zip)

  • v.1.4.3(Jul 5, 2022)

    Changes:

    • added spill sensor and turbo sensor
    • added workaround for zones not updating temperatures

    It's been confirmed with Polyaire that there's an issue and update messages are not being sent when zones change temperatures. Current workaround is to ask for zone update messages every time there's an AC update message arriving, this should be every minute or so.

    Source code(tar.gz)
    Source code(zip)

  • v.1.4.2(Jun 29, 2022)

    Improvements:

    • add preset mode to zone thermostats
    • do not send unnecessary messages (airtouch snooping)

    Bug fixes:

    • fixes a bug where AC changes does not update zone thermostats
    Source code(tar.gz)
    Source code(zip)

  • v.1.4.1(Jun 29, 2022)

    Improvements:

    • add preset mode to zone thermostats
    • do not send unnecessary messages (airtouch snooping)

    Bug fixes:

    • fixes a bug where AC changes does not update zone thermostats
    Source code(tar.gz)
    Source code(zip)

  • v.1.4.0(Jun 28, 2022)

    Improvements:

    • Added ITC low battery as binary_sensor (On = low battery)
    • Allow damper setting to be readable while in ITC mode (Note: some cards might still allow to change the value; this will be ignored and a refresh will show the true value...)
    Source code(tar.gz)
    Source code(zip)

  • v.1.3.2(Jun 28, 2022)

    Updated airtouch communication protocol to check for 1 address byte instead of 2 in message header. Should fix issues where some messages where ignored and entities in HA were not updated.

    Source code(tar.gz)
    Source code(zip)

  • v.1.3.1(Jun 24, 2022)

    Changes:

    • 1.3.1: allow more time to set up airtouch connection
    • 1.3.0: improvements in airtouch connection handling

    Note: starting with v.1.3, entities ids have been changed to include entity type. You need to change your cards, scripts and automations according to the new format:

    • AC unit: climate.[name] -> climate.ac_[name] (e.g. climate.ac_lg)
    • Damper: fan.[name] -> fan.damper_[name] (e.g. fan.damper_living)
    • ITC thermostat: climate.[name] -> climate.itc_[name] (e.g. climate.itc_master)
    Source code(tar.gz)
    Source code(zip)

  • v.1.3(Jun 23, 2022)

  • v.1.2.3(Nov 6, 2021)

  • v.1.2.2(Nov 1, 2021)

  • v.1.2.1(Nov 1, 2021)

  • v.1.2.0(Oct 31, 2021)

  • v.1.1.2(Oct 30, 2021)

  • v.1.1.1(Oct 30, 2021)

  • v.1.1.0(Oct 30, 2021)

Owner
GitHub Repository
SALUS THERMOSTAT Custom component for Home-Assistant

Home-Assistant Custom Components Custom Components for Home-Assistant (http://www.home-assistant.io) Salus Thermostat Climate Component My device is R

21 Dec 18, 2022
Segger Embedded Studio project for building & debugging Flipper Zero firmware.

Segger Embedded Studio project for Flipper Zero firmware Установка Добавить данный репозиторий в качестве сабмодуля в корень локальной копии репозитор

25 Dec 28, 2022
Robot Framework keyword library wrapper for atlassian-python-api

Robot Framework keyword library wrapper for atlassian-python-api

Marcin Koperski 3 Jul 29, 2022
Activate Numpad inside the touchpad with top right corner switch or F8 key

This is a python service which enables switching between numpad and touchpad for the Asus UX433. It may work for other models.

Mohamed Badaoui 230 Jan 08, 2023
Home Assistant custom components MPK-Lodz

MPK Łódź sensor This sensor uses unofficial API provided by MPK Łódź. Configuration options Key Type Required Default Description name string False MP

Piotr Machowski 3 Nov 01, 2022
Home Assistant component to handle key atom

KeyAtome Home Assistant component to handle key atom, a Linky-compatible device made by Total/Direct-Energie. Installation Either use HACS (default),

18 Dec 21, 2022
BoneIO is a compact IO controller for home automation.

Project description BoneIO is a compact IO controller for home automation. Main features of this controller are Compact size (27x11x6)cm - 15 DIN modu

Maciej Krasuski 120 Nov 30, 2022
♟️ QR Code display for P4wnP1 (SSH, VNC, any text / URL)

♟️ Display QR Codes on P4wnP1 (p4wnsolo-qr) 🟢 QR Code display for P4wnP1 w/OLED (SSH, VNC, P4wnP1 WebGUI, any text / URL / exfiltrated data) Note: Th

PawnSolo 4 Dec 19, 2022
This OctoPrint plugin will make the initial connection to 3D Hub a breeze

3D Hub Connector This OctoPrint plugin will make the initial connection to 3D Hub a breeze. In future it will help in setting up a tunnel connection a

3D Hub 2 Aug 03, 2022
The robot is an autonomous small scale racing car using NVIDIA Jetson Nano.

The robot is an autonomous small scale racing car using NVIDIA Jetson Nano. This project utilizes deep learning neural network framework Keras/Tensorflow, together with computer vision library OpenCV

1 Dec 08, 2021
Home Assistant custom component to help ev-chargers stay below peak hourly energy levels.

Peaqev ev-charging Peaqev ev-charging is an attempt of charging an ev without breaching a preset monthly max-peak energy level. In order for this inte

Magnus Eldén 35 Dec 24, 2022
A dashboard for Raspberry Pi to display environmental weather data, rain radar, weather forecast, etc. written in Python

Weather Clock for Raspberry PI This project is a dashboard for Raspberry Pi to display environmental weather data, rain radar, weather forecast, etc.

Markus Geiger 1 May 01, 2022
CircuitPython library for the CH559 USB to Serial chip

CH559 (USB to Serial) CircuitPython Library Why? Because you might want to get keyboard/mouse/gamepad/HID input into your CircuitPython projects witho

Guy Dupont 3 Nov 19, 2022
A install script for installing qtile and my configs on Raspberry Pi OS

QPI OS - Qtile + Raspberry PI OS Qtile + Raspberry Pi OS :) Installation Run this command in the terminal

RPICoder 3 Dec 19, 2021
Raspberry Pi Spectrometer

PySpectrometer 2021-03-05 Raspberry Pi Spectrometer The PySpectrometer is a Python (OpenCV and Tkinter) implementation of an optical spectrometer. The

Les Wright 538 Jan 05, 2023
This tool emulates an EMV-CAP device, to illustrate the article "Banque en ligne : à la decouverte d'EMV-CAP" published in MISC

About This tool emulates an EMV-CAP device, to illustrate the article "Banque en ligne : à la decouverte d'EMV-CAP" published in MISC, issue #56 and f

Philippe Teuwen 28 Nov 21, 2022
ArucoFollow - A script for Robot Operating System and it is a part of a project Robot

ArucoFollow ArucoFollow is a script for Robot Operating System and it is a part

5 Jan 25, 2022
A battery pack simulation tool that uses the PyBaMM framework

Overview of liionpack liionpack takes a 1D PyBaMM model and makes it into a pack. You can either specify the configuration e.g. 16 cells in parallel a

PyBaMM Team 40 Jan 05, 2023
Create (templateable) cameras that display qr codes in homeassistant

QRCam This custom component creates cameras displaying qrcodes. The QRCodes can be static or generated from templates. If you use a template as conten

Jannes Müller 5 Oct 06, 2022
CircuitPython Driver for Adafruit 24LC32 I2C EEPROM Breakout 32Kbit / 4 KB

Introduction CircuitPython driver for Adafruit 24LC32 I2C EEPROM Breakout Dependencies This driver depends on: Adafruit CircuitPython Bus Device Regis

foamyguy 0 Dec 20, 2021