Getting to the meat of g-code. Easy, fast, effective, and automatic g-code compression! MeatPack nearly doubles the effective data rate of a standard 115,200 baud-rate serial connection to 210,000 baud!
Firmware with MeatPack Support:
NOTICE: If you have a compatible Creality printer for Marlin Firmware Service, please use the latest firmware image (built after 2021-01-27 12:50:00 UTC) from: https://marlin.crc.id.au/. These builds should all have MeatPack support!
- Marlin (merged Jan. 25, 2021) - NOTICE: It looks like there might be a problem on the official Marlin repo. They merged my PR, but did quite a bit of refactoring, and it may have broken MeatPack support. Use this commit/node to merge (https://github.com/scottmudge/Marlin/commit/01483c9541e3150f809f66c65ae107571797dc6f) until it's worked out. The
MEATPACKprecompiler option should be enabled during build. See note above for compatible Creality printers. - Prusa (official build reviewing support, unofficial build with support available at https://github.com/scottmudge/Prusa-Firmware-MeatPack)
OctoPrint Support:
Should be compatible with any OctoPrint installation providing access to the serial_factory_hook(). According to the API documentation, this was intoruced in OctoPrint version 1.2. As far as Python is concerned, as of MeatPack version 1.5.17, it should be compatible back to 2.7, but it is highly recommended to update to Python 3 if you have not yet done so.
Current Features (v1.5.21)
-
Fully working g-code compression ("MeatPack") support for compatible printer firmwares. Marlin FW now officially supprots MeatPack, but [NOTE] until Prusa approves these changes, please find builds of the official Prusa Firmware with compression support here: https://github.com/scottmudge/Prusa-Firmware-MeatPack
-
Added extra data to the "State" side-bar content, updated in real time. It shows transmission statistics:
- "Packed Tx" - This is the actual amount of data sent over the serial connection. The data that has been packed.
- "Total Tx" - This is the effective amount of data sent over the serial connection, after it is unpacked on the other end. Should be close to the original (though OctoPrint often adds error checking data to lines of g-code, so it will be a bit higher).
- "Comp. Ratio" - This is the compression ratio, bascially a measure of how much bandwidth you are gaining/saving. It's the factor by which the data has been effectively shrunk.
- "TX Rate" - This is a measure of how much data is being sent over the serial connection per second (average). Updated every ~2 seconds.
- "Packing State"-- Lets you know if MeatPack compression is enabled or not.
NOTE: This extra text section can be disabled in the plugin options page.
-
A feature called "Whitespace Removal", which strips away all unnecessary whitespace from outgoing gcode on the serial port. This also allows the 'E' character to be packed in place of the ' ' space character. This effectively boosts the compression ratio down to 0.55!
-
Added an optional feature (can be enabled in plugin settings) to play a "meatball" song on the printer after a print is completed. See the bottom of the readme why everything is "meat" themed.
NOTE: To use MeatPack, please install an updated build of Marlin Firmware with MeatPack support integrated, or for Prusa printers, install compatible version of the Prusa firmware here:
Prusa Firmware with MeatPack-support (MP-Firmware v1.1.0, based on Prusa FW 3.9.3): https://github.com/scottmudge/Prusa-Firmware-MeatPack/releases/tag/v3.9.3-MP1.1.0
Installation
UPDATE: OctoPrint has approved this plugin for the official plugin repository, so it should be available to install via the in-built plugin manager now. If you'd still rather manually install it, please follow the instructions below.
- Install via the OctoPrint plugin manager.
-OR-
- Open a terminal or console (or SSH into your Raspberry Pi if using one) and activate OctoPrint's virtual environment (Python). Typically this will be in
~/oprint/. You can activate the virtual environment by using the following command:
source ~/oprint/bin/activate
- After activating the OctoPrint environment, run the following command:
pip install https://github.com/scottmudge/OctoPrint-MeatPack/archive/v1.5.9.zip
-
Restart your OctoPrint server, or restart the machine.
-
After installation, you should see a "MeatPrint" options page, and a new "TX Statistics" section in the "State" side bar section (if connected to your printer).
Known Limitations:
-
This requires a minor modification to your printer's firmware! Marlin has officially adopted support, but Prusa is currently reviewing changes. I have currently compiled modified firmware for Prusa's MK3/3S printers, available above.
-
It doesn't work with the Virtual Printer in OctoPrint. Obviously... it's not a real serial connection.
Why compress/pack G-Code? What is this?
It's been often reported that using OctoPrint's serial interface can often cause performance bottlenecks for printer firmware. Many popular printers (e.g., Prusa's MK3) are limited to ~115200 baud. For many simple prints, this works fine. But for prints with numerous, small, or quickly-traversed curves, this can pose a problem.
In g-code, these many small curves are broken down into very short line-segments. These line segments are each described as cartesian points, for instance:
...
G1 X125.824 Y95.261 E0.00907
G1 X125.496 Y95.249 E0.01145
G1 X123.181 Y92.934 E0.11420
...
All this text might describe only a couple hundred microns of travel. When printing at higher speeds, you can see how much text actually needs to be transferred over the serial connection.
This can cause stuttering or other issues while printing, leading to sub-par print quality.
There have been a few attempts to get around this problem in the past. One example, Arc Welder, replaces these linear line segments with close-approximate arc equivalents (radians + radius). This does solve the problem of reducing g-code size, but not all printer firmwares are compatible with these arc-type g-codes, and it is left up to the printer firmware to linearize these arcs back into cartesian line segments. Not all firmwares do this well, and often the firmware CPU can be bogged down with this costly computation.
So what does MeatPack do?
MeatPack takes a different approach. Instead of modifying the g-code or replacing commands, it insteads uses a more efficient way of transferring the data from PC/Host to Firmware.
G-code at its core is a fairly simple language, which uses a restricted alphabet. There are only a few characters which are actually being used to represent a vast majority of g-code -- numbers, decimal point, a few letters ('G', 'M', 'E', etc.), and other utilitiy characters (newline, space, etc.).
I performed a basic histographic analysis of about a dozen g-code files, and found that ~93% of all g-code uses the same 15 characters! And yet we are using characters sized to fit a potential 256-character alphabet!
So what MeatPack does is get to the meat of the g-code! At its core, MeatPack is dynamically packing 2 characters into a single 8-bits/1-byte, effectively doubling data density. Using a lookup table, MeatPack is able to represent any character from the list of the 15-most-common found in g-code with only 4-bits.
Why only 15-most common if 4-bits allows 16 possible characters? Well I also needed a way to send full-width characters in the event that any character does not fall into the list of the 15-most common. So the 16th permutation (0b1111) is used as a flag to tell the unpacker that it should expect a full-width character at some point.
MeatPack also provides for a rudimentary communication/control layer by using a special character (0xFF) sent in a specific sequence. 0XFF is virtually never found naturally in g-code, so it is can be considered a reserved character.
How does it work?
Here is an example. Take the following "G1" command.
G1 X113.214 Y91.45 E1.3154
Unpacked, it is sent as distinct bytes (B):
(G) (1) ( ) (X) (1) (1) (3) (.) (2) (1) (4) ( ) (Y) (9) (1) (.) (4) (5) ( ) (E) (1) (.) (3) (1) (5) (4) (\n)
In total, 27 bytes.
It is effectively packed as the following -- note that parenthetical groups (XX) indicate that the contents are packed as a single byte:
(G1) ( X) (11) (3.) (21) (4 ) (9#)* (Y) (1.) (45) (# )* (E) (1.) (31) (54) (\n)
or with "Whitespace Removal" active:
(G1) (X1) (13) (.2) (14) (9#) (Y) (1.) (45) (E1) (.3) (15) (4\n)
* these bytes don't show character order, but bit order. Higher order bits on left, lower order bits on right. See below. The other characters are sequential and only show how they are paired in bytes.
The packer reorders some characters if the full width character is surrounded by packable characters. The # here is a flag (0b1111) which tells the unpacker where the following full width character should go.
In this way, 4 bits aren't wasted telling the packer that only one full width character is coming up. 0xFF (0b11111111) tells the unpacker that the next 2 bytea are full width.
If 0b1111 is in the lower 4 bits, the full width character is immediately following, and the packed character in the upper 4 bits goes after the full width character. If it's in the higher 4 bits, the full width character goes after the character packed in the lower 4 bits. And if both upper and lower 4 bits are set to 1111, the next 2 characters are full width.
So 16 bytes in this example (13 bytes with Whitespace Removal active). This is on-par or better than binary packing. With whitespace removal active, the packed command is less than half the size of the original command.
This minor reordering is undone in the unpacking stage in the firmware. A little more complex, but it allows slightly more data to be packed.
This is also why the command sequence is 2 0xFF bytes in a row, followed by a command byte. If packing is enabled, 0xFF means the next character is some standard ASCII character (or at the very least not 0xFF), so 2 0xFF bytes in a row would never occur naturally except in these control/command sequences. And if packing is disabled, 0xFF is an invalid g-code character (the Prusa firmware even discards all bytes higher than 127U). This command signal preamble can be increased to 3 or more 0xFF bytes if some firmwares tend to have these bytes in error more frequently. But from what I've seen, it's generally 0x0 or null bytes which are received or sent in error. For instance, in noisy or unshielded connections.
Why "Meat"?
My cat's name is Meatball, I thought it sounded fun.
Obligatory cat photo:
![[Enhancement] Dynamic size display adjustment](https://avatars.githubusercontent.com/u/33363128?v=4)
612 Jan 04, 2023
26 Dec 14, 2022
40 Nov 25, 2022
74 Oct 07, 2022
1 Aug 15, 2022
45 Jan 05, 2023
7 Jan 15, 2022
132 Dec 26, 2022
29 Dec 05, 2022
50 Mar 22, 2022
49 Dec 06, 2022
111 Dec 23, 2022
7 Sep 20, 2022
2 Jan 16, 2022
0 Jan 05, 2022
4 Feb 27, 2022
63 Dec 25, 2022
740 Dec 24, 2022
3.1k Jan 08, 2023
1 Oct 05, 2021